不同点火位置时乳胶泡沫火蔓延特性

doi:10.12034/j.issn.1009-606X.217415

过程工程学报 ›› 2018, Vol. 18 ›› Issue (5): 1029-1036.DOI: 10.12034/j.issn.1009-606X.217415

不同点火位置时乳胶泡沫火蔓延特性

张明振¹，黄冬梅^1,2*，原琪¹，王姝雯¹

1. 中国计量大学质量与安全工程学院，浙江杭州 310018 2. 浙江省家具检测技术研究重点实验室，浙江杭州 310018

收稿日期:2017-11-29 修回日期:2018-03-03 出版日期:2018-10-22 发布日期:2018-10-12
通讯作者: 黄冬梅 dmhuang@cjlu.edu.cn
基金资助:
火灾烟气对二氧化硅气凝胶复合材料隔热性能影响机理的研究;床垫填充材料乳胶泡沫水平火蔓延行为

Flame spread characteristics of latex foam at different ignition positions

Mingzhen ZHANG¹, Dongmei HUANG^1,2*, Qi YUAN¹, Shuwen WANG¹

1. College of Quality and Safety Engineering, China Jiliang University, Hangzhou, Zhejiang 310018, China
2. Key Laboratory of Furniture Inspection Technology of Zhejiang Province, Hangzhou, Zhejiang 310018, China

Received:2017-11-29 Revised:2018-03-03 Online:2018-10-22 Published:2018-10-12

摘要/Abstract

摘要： 在边缘点火和中间点火条件下对多孔乳胶泡沫进行小尺寸燃烧，研究了不同点火位置时火焰的蔓延过程和规律，考察了材料表面温度分布、火蔓延速率和火焰高度随时间的变化. 结果表明，边缘和中间点火时，平均火蔓延速率分别为0.42和0.24 cm/s，蔓延至整个材料表面的时间分别为84和74 s，最大火焰高度分别为68.6和82.7 cm. 随火焰区不断增大，火焰温度不断升高，传递给未燃区的热量增多，加速了材料热解，火蔓延速率增大.

关键词: 点火位置, 水平火蔓延, 火蔓延速率, 乳胶泡沫, 火焰高度

Abstract: Natural latex based furniture is widely used in our daily lives. However, it is very easy to be ignited. Once ignited, fire could spread remarkably fast companied with a large amount of heat, smoke and fumes, which are extremely harmful to human beings. It makes sense to study the flame spread of latex foam. In this paper, the influence of ignition positions on the flame spread characteristics of latex foam were analyzed experimentally using a small-scale experimental setup and the ignition point was put on the center and edge of the specimen. The surface temperature profiles, flame height and flame spread rate were measured. The results showed that the latex foam combustion process can be divided into 5 stages: heat absorption, pyrolysis, ignition, heat transfer and flame spread. The flame spread direction was from the center to the edge showing a circle shape for the center ignition conditions. For the edge ignition condition, flame spread from one edge point to the diagonal point with the shape of sector. The average flame rate and the time of flame spread to whole surface of material for edge ignition condition were much higher than that of the center ignition condition. The average flame rates for edge and center ignition conditions were 0.42 and 0.24 cm/s, respectively. However, maximum flame height under edge ignition condition showed a lower value than those under center ignition condition, which is 68.6 cm comparing to 82.7 cm. The scale of burnt zone under two conditions expanded gradually with an increase of flame temperature. Therefore, more energy was passed to unburnt zone, which led to the speed up of material pyrolysis and the increase of flame spread rate. The heat transfer mechanism of the sample was investigated. In practice, this study can have a practically guiding meaning for fire protection and rescue.

Key words: ignition location, horizontal fire spread, fire spread rate, latex foam, flame height

张明振黄冬梅郭晨宁王姝雯. 不同点火位置时乳胶泡沫火蔓延特性[J]. 过程工程学报, 2018, 18(5): 1029-1036.

Mingzhen ZHANG Dongmei HUANG Qi YUAN Shuwen WANG. Flame spread characteristics of latex foam at different ignition positions[J]. Chin. J. Process Eng., 2018, 18(5): 1029-1036.

参考文献

[1].[J]., 2012, :1524-1529 [2] 李玉芳, 李明.ABS 树脂阻燃剂的研究开发进展[J]. 塑料制造, 2012 (6): 16-20. [3]Li Y F, Li M.Advances in Research and Development of ABS Resin Flame Retardants [J]. Plastics Manufacturing, 2012 (6): 16-20. [4] D.Madrzykowski, N.Bryner, W. Grosshandler, D. Stroup, Fire spread through a room with polyurethane foam covered walls, in, 2004, pp. 1127-1138. [5]Holleyhead R.Ignition of solid materials and furniture by lighted cigarettesA review[J].Science & Justice, 1999, 39(2):75-102 [6]Woolley W D, Ames S A, Pitt A I, et al.Fire behaviour of beds and bedding materials[J].Fire and Materials, 1976, 1(2):63-73 [7] 祝佳琰, 典型软垫家具火灾特性的实验研究, in, 中国科学技术大学, 2006. [8]Zhu J Y, Zhu W B, Wang W.Study on Small-size Experimental Study on Fire Characteristics of Typical Upholstered Furniture Materials [J]. Journal of Fire Science, 2006, (02): 86-91 + 52. [9] Prasad K, Kramer R, Marsh N, et al.Numerical simulation of fire spread on polyurethane foam slabs[C]//Fire Research Division, BFRL, NIST Annual Fire Conference. 2009. [10]. Zhang Y, Ji J, LiJ, etal． Effects of altitude and sample width on the characteristics of horizontal flame spread over wood sheets［J］． Fire Safety Journal，2012，51: 120－125． [11]Chen P, Sun J H，He X C.Behavior of flame spread downward over thick wood sheets and heat transfer analysis[J].Journal of Fire Sciences, 2007, 25(1):5- [12] 朱超, 张英, 孙金华.试样放置角度与外加辐射强度对可碳化固体表面火蔓延的影响[J]. 火灾科学, 2010, (04):232-238. [13]Zhu C, Zhang Y, Sun J H.Effects of Sample Placement Angle and External Radiation Intensity on Spontaneous Combustion of Carbonizable Solid Surfaces [J]. Fire Science, 2010, (04): 232-238. [14] 王渊明, 赵恒泽, 赵兰明, 王进军, 方俊, 张永明.试样宽度对RPU板竖向逆流火蔓延的影响[J]. 燃烧科学与技术, 2013, (04):365-370. [15]Wang Y M, Zhao H Z, Zhao LM, et al.Influence of sample width on vertical countercurrent fire propagation of RPU plate [J]. Combustion Science and Technology, 2013, (04): 365-370. [16]王杰, 崔超.工业用热电偶现场校准相关问题的探讨[J]. 中国标准导报, 2016 (2016 年 02): 46-48, 52. [17]Wang J, Cui C.Research on the field calibration of industrial thermocouple [J]. 中国标准导报, 2016 (2016 年 02): 46-48, 52. [18]Atreya A, Baum H R.A model of opposed-flow flame spread over charring materials[J].Proce- edings of the Combustion Institute, 2002, 29(1):227-236 [19] 黄新杰, 张英, 纪杰, 尹艺, 孙金华.拉萨和合肥环境下不同厚度保温材料XPS的火蔓延特性[J]. 燃烧科学与技术, 2011, (06):527-533. [20]Hhang X J, Zhang Y, Ji J, et al.Flame Spread Characteristics of XPS with Different Thickness of Thermal Insulation Material in Lhasa and Hefei [J]. Combustion Science & Technology, 2011, (06): 527-533. [21]陈鹏.典型木材表面火蔓延行为及传热机理研究[D].中国科学技术大学, 2006. [22]Chen P.Fire propagation behavior of typical wood surfaces and heat transfer mechanism [D]. University of Science and Technology of China, 2006. [23] Atreya A.Pyrolysis, ignition and fire spread on horizontal surface of wood[ D]. Cambridge:Havard University, Ph/D. Thesis, 1983. [24] Quintiere JG (2006) Fundamentals of fire phenomena.Wiley, New York. [25] Fernandez-Pello A C, Ray S R, Glassman I.Flame spread in an opposed forced flow: The effect of ambient oxygen concentration［C］.Eighteenth Symposium ( International) on Combustion. The Combustion Institute． Pittsburgh，1981: 579－589． [26]Zhang X, Yu Y.Experimental studies on the three-dimensional effects of opposed-flow flame spread over thin solid materials[J].Combustion and Flame, 2011, 158(6):1193- [27] Saito K, Quintiere JG, Williams FA (1985) Upward turbulent flame spread.In: Proceedings of the First International Symposium on Fire Safety Science, pp 75–86. [28] B.Karlsson, J. Quintiere, Enclosure fire dynamics, CRC press, 1999. [29] Fan H, Chen Y, Huang D, et al.Kinetic Analysis of the Thermal Decomposition of Latex Foam according to The rmogravimetric Analysis[J]. International Journal of Polymer Science, 2016, 2016.

不同点火位置时乳胶泡沫火蔓延特性

Flame spread characteristics of latex foam at different ignition positions

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics

[1]	刘珂张英张威吴淑娴潘文砚. 可膨胀石墨和碳纳米管对PMMA火蔓延特性的影响[J]. 过程工程学报, 2021, 21(9): 1054-1063.
[2]	赵杰黄新杰刘伟张英孙金华. 不同宽度及密度的保温材料EPS的火焰蔓延及燃烧特性[J]. 过程工程学报, 2016, 16(3): 463-469.
[3]	夏亮;赵黛青;山下博史;汪小憨. 旋转流中预混合火焰高速传播现象-II. 点火位置与燃烧过程[J]. , 2007, 7(3): 462-466.