轴向旋流式微气泡发生器的结构设计与数值模拟

doi:10.12034/j.issn.1009-606X.217413

摘要/Abstract

摘要： 设计了一种旋流式微气泡发生器，由环形注气机构和新型气泡破碎机构两部分组成，前者采用中心圆环+微孔板结构，后者由静止起旋元件和文丘里管组成，采用ANSYS FLUENT软件对新型气泡破碎机构的流道进行数值模拟，并与常规文丘里流道对比. 结果表明，新型气泡破碎机构流道内的水流速度、径向速度梯度、湍动能和湍能耗散率均大于常规文丘里流道，常规文丘里流道出口处产生的微气泡直径为新型气泡破碎机构的2倍. 采用响应曲面法优化静止起旋元件结构，优化后的叶片出口角度为35?，中心圆柱体直径为12.3 mm，叶片长度为10 mm，优化后的气泡破碎机构产生的微气泡直径为优化前的75%.

关键词: 气液两相流, 微气泡发生器, 静止起旋元件, 文丘里管, 数值模拟, 湍流

Abstract: A swirling-type micro-bubble generator was designed in this paper. The main structure of swirling-type microbubble generator consisted of annular gas injection mechanism and new-type bubble breaking mechanism. Among this, the annular gas injection mechanism adopted the structure of “center ring+micro-plate”. The new-type bubble breaking mechanism was composed of the static swirl element and the venturi tube. The static swirl element was coaxially set in the inlet section of venturi tube. Compared with traditional venturi tube, the new-type bubble breaking mechanism had some technical advantages and may produce much smaller microbubbles. With the help of ANSYS FLUENT software, the numerical simulation of the flow path of the new bubble breaking mechanism was carried out and compared with the conventional venturi flow path. The simulation results showed that the velocity, radial velocity gradient, turbulent kinetic energy and turbulent dissipation rate in the new bubble flow path were larger than those of the conventional venturi channel. By introducing the simulated data into the empirical formula, the calculated particle size of micro-bubbles produced at the exit of traditional venture tube was about 2 times of the new bubble breaking mechanism. The results indicated that the new bubble breaking mechanism can produce smaller microbubbles. In order to improve the bubbling efficiency of axial swirling type microbubble generator, the optimization design of new type bubble breaking mechanism was taken. The structure of the rotating element was optimized by the corresponding surface method. The optimized blade exit angle was 35°, the center cylinder diameter was 12.3 mm, and the leaf length was 10 mm. The particle size of micro-bubbles produced by the optimized bubble breaking mechanism was calculated to be 75% before optimization, which indicated that the optimized new type bubble breaking mechanism can deeply improve bubbling efficiency of axial swirling type microbubble generator.

Key words: gas-liquid flow, micro-bubble generator, static swirl element, venturi tube, numerical simulation, turbulent flow

丁国栋陈家庆王春升尚超刘美丽蔡小垒姬宜朋. 轴向旋流式微气泡发生器的结构设计与数值模拟[J]. 过程工程学报, 2018, 18(5): 934-941.

Guodong DING Jiaqing CHEN Chunsheng WANG Chao SHANG Meili LIU Xiaolei CAI Yipeng JI. Structural design and numerical simulation of axial-swirling type micro-bubble generator[J]. Chin. J. Process Eng., 2018, 18(5): 934-941.

参考文献

[1]Rodríguez-Rodríguez J, Sevilla A, Martínez-Bazán C, et al.Generation of microbubbles with applications to industry and medicine[J].Annual Review of Fluid Mechanics, 2015, 47(1):405-429 [2] Marui T.An introduction to micro/nano-bubbles and their applications[C]//The 14th World Multi-Conference on Systemics, Cybernetics and Informatics. Orlando: International Social Science Council, 2010: 43-48. [3]Terasaka K, Hirbayashi A, Nishino T, et al.Development of microbubble aerator for waste water treatment using aerobic activated sludge[J].Chemical engineering science, 2011, 66(14):3172-3179 [4]Yun J E, Kim J H.Development of Venturi System for Microbubble Generation[J].Transactions of the Korean Society of Mechanical Engineers B, 2014, 38(10):865-871 [5]Meakhail T, Teaima I.Experimental and numerical studies of the effect of area ratio and driving pressure on the performance of water and slurry jet pumps[J].Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 2012, 226(9):2250-2266 [6] 唐文偲.气泡发生器结构与性能研究[D]. 哈尔滨: 哈尔滨工程大学, 2014. [7]Tang W S.Study of the structure and performance of bubble generator[D]. Harbin: Harbin Engineering University, 2014 [8]魏月友, 孙姣, 陈文义.基于数值模拟的气泡发生器结构优化研究[J].矿山机械, 2015, 43(6):99-102 [9]Wei Y Y, Sun J, Chen W Y.Study on structural optimization of bubble generator based on numerical simulation[J].Mining Machine, 2015, 43(6):99-102 [10]Tabei K, Haruyama S, Yamaguchi S, et al.Study of micro bubble generation by a swirl jet[J].Journal of Environment and Engineering, 2007, 2(1):172-182 [11]谷脇充浩, 本田真一, 上田健士, 等.対向した台の旋回式マイクロバブル発生装置の干渉[J].日本流体力学会誌, 2008, 27(2):133-141 [12]Hiroyuki T, Shinichi H, Kenji U, et al.Interference of two opposing swinging microbubble generators[J].Journal of the Japan Fluid Mechanics Association, 2008, 27(2):133-141 [13]Sato K.Recent patents on micro-and nano-bubble applications and potential application of a swirl-type generator[J].Recent Patents on Mechanical Engineering, 2011, 4(3):202-211 [14] Ohnari H.Swirling fine-bubble generator: US6382601[P]. 2002-05-07. [15] Ohnari H.Swing type fine air bubble generating device: US7261283[P]. 2007-08-28. [16] 岛田晴示, 浅里信之, 森崎亘.微气泡发生装置: CN104039432A[P]. 2012-12-21. [17]Shimada C, Nobuyuki A, Watari M.Micro-bubble generating device: CN104039432A[P]. 2012-12-21. [18] 嵯峨秀一, 浅里信之.一种微气泡发生装置及回旋流发生装置: CN104023833B[P]. 2012-12-21. [19]Shuichi S, Nobuyuki A.A microbubble generating apparatus and a swirling flow generating apparatus: CN104023833B[P]. 2012-12-21. [20] Abe H, Matsuuchi K, Idaka M.Micro-bubble generator, vortex breakdown nozzle for micro-bubble generator, vane swirler for micro-bubble generator, micro-bubble generating method, and micro-bubble applying device: US7997563[P]. 2011-08-16. [21]Kogawa H, Naoe T, Kyotoh H, et al.Development of microbubble generator for suppression of pressure waves in mercury target of spallation source[J].Journal of Nuclear Science and Technology, 2015, 52(12):1461-1469 [22]杨涛, 李浙昆, 张永忍, 等.旋流式微泡发生器的设计与试验研究[J].水利水电技术, 2016, 47(5):141-144 [23]Yang T, Li Z K, Zhang Y R, et al.Design and experimental study of swirling microbubble generator[J].Water Resources and Hydropower Engineering, 2016, 47(5):141-144 [24] 邓久帅, 李浙昆, 何伟, 等.一种旋流式微气泡发生器及生成微泡的方法: CN104117299A[P]. 2014-10-29. [25]Deng J S, Li Z K, He W, et al.A swirling microbubble generator and a method for generating microbubbles: CN104117299A[P]. 2014-10-29. [26] 邢新会, 吕奉祥, 初里冰, 等.一种微米气泡的发生装置及其专用旋流器: CN101565230A[P]. 2008-04-24. [27]Xing X H, Lv F X, Chu L B, et al.A micro-bubble generation device and its special cyclone: CN101565230A[P]. 2008-04-24. [28] 章成武, 郝海保, 张瑞革, 等.一种石油水处理用气浮选微气泡加气装置及其使用方法: CN106277150A[P]. 2016-09-07. [29]Zhang C W, He H B, Zhang D G, et al.An air flotation micro-bubble aeration device for petroleum water treatment and its using method: CN106277150A[P]. 2016-09-07. [30] 张永忍.自吸式旋流微泡发生器的试验与研究[D]. 昆明: 昆明理工大学, 2015. [31]Zhang Y R.Experiment and research on self-priming swirling bubble generators[D]. Kunming: Kunming University of Science and Technology, 2015. [32] Li Z K, Shi W L, He W, et al.Computer Simulation Method for the Bubbling Performance of the Vortex Micro-bubble Generator[C]// International Conference on Electro mechanical Control Technology and Transportation. France: Atlantis Press, 2015: 250-253. [33]吕奉祥, 初里冰, 周军, 等.新型微米曝气设备的研制及其性能[J].化工学报, 2011, 62(6):1537-1542 [34]Lv F X, Chu L B, Zhou J, et al.Development and performance of a new type of micro aeration equipment[J].CIESC Journal, 2011, 62(6):1537-1542 [35] Yin J, Li J, Li H, et al.Experimental study on the bubble generation characteristics for an venturi type bubble generator[J]. International Journal of Heat and Mass Transfer, 2015, 91: 218-224. [36]马亚鹏, 李浙昆.内腔直径对自吸式旋流微泡发生器内流场的影响[J].机械制造, 2016, 54(11):27-28 [37]Ma Y P, Li Z K.Effect of cavity diameter on flow field in self-sucking swirling bubble generators[J].Machine made, 2016, 54(11):27-28 [38] Rabe K, Hardli L.Flotation unit for purifying water, such as a CFU (compact flotation unit): US9284199[P]. 2016-03-15. [39]Ghanem A, Lemenand T, Della V D, et al.Static mixers: Mechanisms,applications,and characterization methods–A review[J].Chemical Engineering Research and Design, 2014, 92(2):205-228 [40]Paglianti A.Recent innovations in turbulent mixing with static elements[J].Recent Patents on Chemical Engineering, 2008, 1(1):80-87 [41]Casidy J J, Falvey H T.Observations of unsteady flow arising after vortex breakdown[J].Journal of Fluid Mechanics, 1970, 41(4):727-736 [42]Spall R E, Gatski T B, Grosch C E.A criterion for vortex breakdown[J].Physics of Fluids, 1987, 30(11):3434-3440 [43]Hiroyuki K, Takashi N, Harumichi K, et al.Development of micro-bubble generator for suppression of pressure waves in mercury target of spallation source[J].Journal of Nuclear Science & Technology, 2015, 52(12):1-9 [44]金有海, 范超.导叶式旋风管叶片参数设计方法的研究[J].化工机械, 1999, 26(1):21-24 [45]Jin Y H, Fan C.Research on the parameter design method of the guide blade cyclone[J].Chemical machinery, 1999, 26(1):21-24 [46] 雷秉秉.轴流导叶式旋流分离器的数值模拟与实验性能研究[D]. 北京: 北京交通大学, 2017. [47]Lei B B.Numerical simulation and experimental research on axial guide vane cyclone[D]. Beijing: Beijing Jiaotong University, 2017. [48] Fujiwara A, Takagi S, Matsumoto Y.Bubble breakup phenomena in a venturi tube[C]// Asme/jsme 2007, Joint Fluids Engineering Conference. 2007: 553-560. [49] Gabbard C H.Development of a Venturi Type Bubble Generator for Use in the Molten-Salt Reactor Xenon Removal System[D]. Oak Ridge: Oak Ridge National Laboratory, 1972. [50] Kress T S.Mass Transfer Between Small Bubbles and Liquids in Cocurrent Turbulent Pipe Flow[D]. Tennessee: University of Tennessee, 1972. [51]Lasheras J, Martinezbzan C, Montanes J.On the breakup of an air bubble injected into a fully developed turbulent flowI-Breakup frequency[J].Journal of Fluid Mechanics, 2013, 401(401):157-182