欢迎访问过程工程学报, 今天是

过程工程学报 ›› 2020, Vol. 20 ›› Issue (11): 1248-1256.DOI: 10.12034/j.issn.1009-606X.219363

• 流动与传递 • 上一篇    下一篇

内插螺旋立式上行管流场及传热性能的实验研究

彭德其1*,杨春霞1,张建平1,俞天兰2,叶为标1,李昊1   

  1. 1. 湘潭大学机械工程学院,湖南 湘潭 411105 2. 湖南工业大学机械工程学院,湖南 株洲 412007
  • 收稿日期:2019-12-09 修回日期:2020-02-26 出版日期:2020-11-22 发布日期:2020-11-20
  • 通讯作者: 彭德其 pengshuaike@163.com
  • 基金资助:
    锅炉换热管内液固颗粒多尺度流动行为与强化传热机理研究

Experimental study on flow field and heat transfer performance of insert-spiral vertical upstream tube

Deqi PENG1*, Chunxia YANG1, Jianping ZHANG1, Tianlan YU2, Weibiao YE1, Hao LI1   

  1. 1. School of Mechanical Engineering, Xiangtan University, Xiangtan, Hunan 411105, China 2. School of Mechanical Engineering, Hunan University of Technology, Zhuzhou, Hunan 412007, China
  • Received:2019-12-09 Revised:2020-02-26 Online:2020-11-22 Published:2020-11-20
  • Contact: De-Qi PENG pengshuaike@163.com

摘要: 通过粒子图像测速流场实验与传热实验相结合,研究了内插螺旋立式上行管的螺旋节距、丝径、中径比等结构参数在不同Re下对流场、阻力及传热性能的影响。结果表明,内插螺旋能够有效扰动和混合管内流体,使管内形成多个纵向旋涡的流体结构、增大管壁附近液体涡量,有利于强化传热。当Re相同时,管内平均流速v、Nu和综合换热性能PEC均随丝径增大而增大,随中径比减小而增大;随节距增大,3种参数均出现增大的趋势,节距大于20 mm后开始减小。管内流体的阻力f随丝径和节距增大而减小,随中径比增大而增大。综合比较,在较低Re时,节距p=20 mm、丝径e=1.6 mm、中径比D/d=0.75时综合传热效果最好。

关键词: 粒子图像测速, 流场, 传热, 螺旋, 结构参数

Abstract: Through the particle image velocimeter (PIV) flow field experiment combined with heat transfer experiments, the effects of structural parameters such as spiral pitch, wire diameter and median diameter ratio of insert-spiral vertical upstream tube on the flow field and heat transfer performance were studied under different Reynolds number. The results showed that the insert-spiral can effectively disturb and mix the fluid in the tube, and a number of longitudinal vortexes were formed in the tube, and the vorticity of liquid increased near the wall of the tube, which was beneficial to the enhancement of heat transfer. When the Re number was the same, the average flow velocity v, Nu number and the comprehensive heat exchange performance (PEC) in the tube increased with the increase of the wire diameter, and increased with the decrease of the median diameter ratio. As the pitch increased, all three parameters tended to increase, and began to decrease when the pitch was greater than 20 mm. The resistance coefficient f of the fluid in the tube decreased with the increase of the wire diameter and the pitch, and increased with the increase of the median diameter ratio. In general, when the Re number was lower, the comprehensive heat transfer effect was best with a pitch of p=20 mm, a wire diameter of e=1.6 mm, and a median diameter ratio of D/d=0.75.

Key words: particle image velocimeter (PIV), flow field, heat transfer, spiral, structural parameter