基于偏态和峰度的丁胞传热管性能分析

doi:10.12034/j.issn.1009-606X.220101

过程工程学报 ›› 2021, Vol. 21 ›› Issue (5): 530-540.DOI: 10.12034/j.issn.1009-606X.220101

基于偏态和峰度的丁胞传热管性能分析

廖文玲*

成都工业学院智能制造学院，四川成都 611730

收稿日期:2020-03-22 修回日期:2020-06-19 出版日期:2021-05-22 发布日期:2021-06-01
通讯作者: 廖文玲 lwlcdtu18@163.com
基金资助:
成都工业学院校级科研项目

Performance analysis of dimpled tube based on skewness and kurtosis

Wenling LIAO*

School of Intelligent Manufacturing, Chengdu Technological University, Chengdu, Sichuan 611730, China

Received:2020-03-22 Revised:2020-06-19 Online:2021-05-22 Published:2021-06-01
Contact: Wen-ling LIAO lwlcdtu18@163.com

摘要/Abstract

摘要： 建立含不同参数的正六边形截面丁胞传热管有限元分析模型，仿真研究雷诺数为5000~40000时丁胞组合类型、深度和直径对传热管中流体流动及传热性能的影响。此外，采用离散方法计算并分析丁胞参数对传热管表面偏态和峰度的影响。最终基于丁胞参数对偏态和峰度的影响规律对丁胞传热管的性能进行分析。研究结果表明，凹坑或凸起丁胞通过增强流体的回流效果及削弱流体边界层厚度，能够有效增强传热管内流体的流动及传热性能，且凹坑丁胞的影响优于凸起丁胞。此外，不同丁胞组合类型的影响表现为偏态越小、传热管的流动及传热综合性能越好。然而，对于凹坑丁胞传热管，其表面偏态越大、峰度越小，传热管的流动及传热综合性能越好，增加凹坑丁胞深度和直径可增大偏态、减小峰度。

关键词: 传热管, 丁胞, 流动特性, 传热特性, 偏态, 峰度

Abstract: In this work, the numerical simulation model of the hexagonal tube with different parameter dimples has been established considering thermal-hydraulic performance. The effect of dimple types, dimple depth, and dimple diameter on the flow field characteristics, and heat transfer characteristics of dimple tubes were discussed under Reynolds numbers between 5000 and 40000. Skewness and kurtosis of dimpled tube wall surface were calculated by discrete method, and then the thermal-hydraulic performance of dimpled tube was analyzed based on the influence of dimple parameters on skewness and kurtosis. The results showed that the dimpled tube had a better thermal-hydraulic performance due to the recirculation flows and flow separation was a significant increase, and the effect of pit dimple was better than that of bulge dimple. In addition, the influence of different dimple types was that the less the skewness, the better the thermal-hydraulic performance of the heat transfer tube. However, for the pit dimple tube, the larger skewness and the smaller the kurtosis was, the better comprehensive performance of the thermal-hydraulic got. With the increase of the pit dimple depth and diameter, the skewness gradually increased, while the kurtosis value gradually decreased.

Key words: Heat transfer tube, dimple, flow characteristic, heat transfer characteristic, skewness, kurtosis

廖文玲. 基于偏态和峰度的丁胞传热管性能分析[J]. 过程工程学报, 2021, 21(5): 530-540.

Wenling LIAO. Performance analysis of dimpled tube based on skewness and kurtosis[J]. The Chinese Journal of Process Engineering, 2021, 21(5): 530-540.

[1]	李修真谈莹莹袁俊飞王占伟王林. 扭曲椭圆管强化传热研究进展及应用[J]. 过程工程学报, 2022, 22(5): 561-572.
[2]	朱梓瑞刘雪东蒋良雄顾宇彤彭涛殷俊杰刘梅华蒋威. 管式固定床反应器柱状颗粒床层流体流动模拟与实验研究[J]. 过程工程学报, 2021, 21(9): 1022-1032.
[3]	王丽丽张玉柱龙跃王子兵客海滨. 气淬粒化高炉熔渣液膜流动特性数值模拟[J]. 过程工程学报, 2020, 20(8): 887-895.
[4]	李雅侠张元张静寇丽萍龚斌吴剑华. 射流强化螺旋通道内流体流动与换热的数值模拟[J]. 过程工程学报, 2020, 20(8): 896-903.
[5]	傅梦倩姚秀颖范怡平卢春喜. 双层喷嘴提升管进料区内气固流动特性的数值模拟[J]. 过程工程学报, 2020, 20(7): 757-769.
[6]	王来勇钱付平朱景晶黄乃金徐兵吴昊. 选择性催化还原蜂窝状催化剂内流动特性的多尺度模拟[J]. 过程工程学报, 2020, 20(2): 133-140.
[7]	时瑶王德武赵斌张少峰梁凯光马树辉. 旋流筛板式气固挡板流化床内压力脉动特性[J]. 过程工程学报, 2019, 19(1): 91-101.
[8]	鲁进利吕勇军韩亚芳钱付平. 细小槽道换热器内相变微胶囊悬浮液对流传热DPM模拟[J]. 过程工程学报, 2018, 18(5): 951-956.
[9]	鲁进利赵伟池帮杰韩亚芳钱付平. 不同结构细小槽道热沉流量均匀性 [J]. , 2017, 17(1): 58-63.
[10]	张珺刘有智焦纬洲祁贵生. 三股对撞式撞击流反应器的流动特性[J]. , 2015, 15(2): 218-223.
[11]	沈志远杨利军刘梦溪卢春喜. 中心气升式气-固环流反应器与自由流化床流动特性对比[J]. , 2014, 14(4): 541-548.
[12]	崔刚刘梦溪卢春喜. 流化床-提升管耦合反应器内固含率的轴向分布及流动发展[J]. , 2014, 14(4): 556-561.
[13]	秦小刚闫子涵张广杰范怡平卢春喜. 流化床-提升管耦合反应器内沥青颗粒的流动特性[J]. , 2013, 13(4): 562-567.
[14]	王翠华唐密吴剑华寇丽萍. 等腰直角三角形截面螺旋流道内层流流体的流动特性[J]. , 2012, 12(5): 754-759.
[15]	孙治谦王振波吴存仙金有海. 油水重力分离过程油滴浮升规律的实验研究[J]. , 2009, 9(1): 23-27.

基于偏态和峰度的丁胞传热管性能分析

Performance analysis of dimpled tube based on skewness and kurtosis

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics